How to Charge a Laptop With a Power Bank

Power banks store electrical energy, and hold it, so that users can plug in later when they need a recharge. They allow tech users to plug into a power source that's mobile; essentially a portable battery with inputs to charge multiple devices. They can charge everything from Smartphones to Laptops simply by plugging into them.



Those looking to purchase a power bank to charge their laptop should remember that they'll need a larger size..

   Battery capacity is measured in terms of milliamps, or mAh. Many laptops have around 5,000 mAh batteries, which means a 2,000 mAh is only enough for less than half a charge. Therefore, a computer with a 5,0000 mAh battery capacity requires a power bank of at least 5,000 mAh to guarantee at least one full charge..


  for big size u should buy powerbank above 5000 mah to charge your laptop...

   it is very easy to use 
connect power bank to your laptop 
u will see it is charging ...

like fb page =www.facebook.com/technoknowledge12

how to download youtube video without using any third party

how to download youtube video without using any third party...
oepn web browser 
go to youtube site
select which one you want video to download 
and select that video then pause video
go to on address bar remove https://www. this things 
and type istead of that "ss" then press enter 
you will see download link and select what you want mp3 or video and select and click on download button ....

if u like this video press thumb button...


or like my facebook page
www.facebook.com/technoknowledge12

boot usb using third party..

1.if no cd is there for booting the pc ..
2.. and cd rom is in bad condition or not working
3.. we can use   third software for booting computer
4.. click below link and download ...
 

https://rufus.akeo.ie/?locale=pt

5- install this n follow in given picture which is below,,..



   

enjoy .....

www.facebook.com/technoknowledge12     like this page get more updates...

How to Create a Bootable USB Drive Without Using Any Software..

To create a bootable USB drive manually, we will use the Command Prompt as a Windows default program. Here are step by step to create a bootable USB drive as the Windows installation media. To create a bootable USB drive as a Windows installation media, we require at least 4 GB for minimum capacity. Larger capacity is better. At this moment, I use the USB flash drive with 2 GB of capacity as just an example...

Step 1: Using DISKPART command.

1. Insert your USB flash drive to your running computer. As the first step, we need to run Command Prompt as administrator. To do this, we need to find cmd by typing 'cmd' in the search box on Windows Start Menu. After search result for 'cmd' appears, right click on it and select "Run as administrator".
2. Type 'diskpart' on Command Prompt (without quotes) and hit Enter. Wait for a while until the DISKPART program run.
3. Type 'list disk' to view active disks on your computer and hit Enter. There would be seen that the active disks shown as Disk 0 for hard drive and Disk 1 for your USB flashdrive with its total capacity.
4. Type 'select disk 1' to determine that disk 1 would be processed in the next step then hit Enter.
5. Type 'clean' and hit Enter to remove all of data in the drive.
6. Type 'create partition primary' and hit Enter. Creating a primary partition and further recognized by Windows as 'partition 1'.
7. Type 'select partition 1' an hit Enter. Choosing the 'partition 1' for setting up it as an active partition.
8. Type 'active' and hit Enter. Activating current partition.
9. Type 'format fs=ntfs quick' and hit Enter. Formatting current partition as NTFS file system quickly.
10. Type 'exit' and hit Enter. Leaving DISKPART program but don't close the Command Prompt instead. We would still need it for next process.

 www.facebook.com/technoknowledge12   like this page ....

using cmd or command create hotspot wifi...

1- if u have ethernet wired connection ,then and 
2- no router is there ,so use this method to create virtual wifi hotspot
3- there is comand method using cmd we can  create hotspot wifi in laptop or pc then you can use any device this hotspot wifi
  


1-use cmd in cmd right click on cmd open as administrator
2-netsh wlan set hostednetwork mode=allow ssid=give ur username key=give passwordminimum 8 characters.
3-netsh wlan start hostednetwork

then go to control pannel and go to network and internet in that see which u have created user name that will be there and click on that and click right and use shared network then it will work good  try it it is very easy....



if any doubt is there then free to ask ...
like facebook page and see latest info on that.....




www.facebook.com/technoknowlede12    

virtual create hotspot if no router is there,,,

1- if u have ethernet wired connection ,then and 
2- no router is there ,so use this method to create virtual wifi hotspot
3- there is one third party software which is given below click on that or copy that link in browser and start download ...
    http://virtualrouter.codeplex.com/downloads/get/621827

then see below is image ,


      

-in that in network name give any name whatever you like...

-in password give any password max 8 chracter

shared connection give which is having your connection wired share with that network which you are using current connection that one...

then start virtual router 

wait for connection then use ur mobile wifi connect this hotspot in your mobile ...

enjoy it...

it is free cost and easy to use 

if you have no money for router this will work fine ...

facebook like page=www.facebook.com/technoknowledge12

Facebook red .apk...

This is a red Facebook ..looking red with beautifull look and same as Facebook app ..

!!= this is an app name is Facebook red.apk 
  Download n use it ..u will enjoy with this app I know....

Download from this link